How Much Does it Cost to Fix a Furnace?

Gas furnace repair in progress

How Much Does it Cost to Fix a Furnace?

On average, homeowners can expect to pay around two-hundred and fifty dollars for a gas furnace repair. It is important to note that this price may vary depending on what problems are occurring with the furnace. The range vacillates between one-hundred and thirty dollars and four-hundred dollars. In some cases, the high end of the spectrum is one thousand dollars.

What Causes a Gas Furnace to Stop Working?

Gas furnace repair and replacement is an important service, particularly in the midst of winter. The causes of furnace failure are varied. However, one of the prominent reasons is a clogged furnace filter. Over time, dust and dirt will clog an air filter, which in turn restricts airflow. When this happens, the heat exchanger overheats and shuts off too soon. This will cause the home not to warm up properly. 

Another potential cause for furnace failure is a thermostat malfunction. Please check to see that your thermostat is on and properly set as a failsafe.

Yet another potential cause is if the circuit breaker has blown or tripped. In terms of troubleshooting your furnace, these are two critical steps in determining the cause of your furnace problems.

How Do You Troubleshoot a Gas Furnace?

The first thing you should do when troubleshooting your furnace is to clean or replace the air filter. As previously mentioned, restricted airflow will cause your furnace to turn off before the home has been properly warmed. Regularly cleaning or replacing the air filter in your furnace will save you from serious furnace problems in the long run. The next step in troubleshooting is investigating your thermostat. Replace the batteries in your thermostat if necessary.

If the problem with your furnace was not identified in earlier steps, please feel free to check the electrical panel for blown fuses or tripped breakers. Finally, sometimes the problem lies with the power switch to the furnace, so please investigate that area.

How Do You Reset Your Furnace?

It is important for homeowners to recognize how to troubleshoot their furnace. This is because a few simple steps can prevent you from having to call a furnace repairman. Please review the following bullet points to learn more.

  • Locate the circuit breaker and turn off power to the furnace. Your circuit breaker should be recognizable through markings.
  • Next, you will lift up the blower compartment cover. Once you have done that, you can approach the blower wheel and motor. You may need a Phillips-head screw for this part. If the housing is hot, please allow it to cool before resetting the rest button.
  • Search for a small red or yellow button that is near the blower motor. It should be on the side. 
  • If it has popped up, please press the reset button down.  Then you can place the blower compartment door back into place and turn the power back on to the furnace.

Is There a Reset Button on a Gas Furnace?

Yes, there is a reset button on a gas furnace. The reason why there is a reset button is to enable a furnace shut off before it can trip the circuit breaker. The reset button becomes important when the furnace gets too hot or if there is an electrical system problem. The roof, the HVAC system, and the plumbing must operate at a high level in order to have maximum efficiency. If you need gas furnace repair in High Point, NC, it is important for you to secure an appointment sooner rather than later. 

Gas Furnace Repair Near Me

If your gas furnace is short-cycling or showing symptoms of disrepair, it’s important to select a qualified and insured HVAC company. In order to find a good HVAC company, first, ask a friend or neighbor for a recommendation or referral. After you have exhausted your contacts, next go to your computer and type in “HVAC company near me” into google. This procedure will give you a list of relevant HVAC companies that are within a certain mile radius. Once you have a good list, next select the companies with reviews that sound authentic. Make sure that your final HVAC company selection specializes in furnace repair. With a little bit of luck and research, you can find an excellent HVAC company nearby.

Gas Furnace Repair Parts

The basic parts of a gas furnace include the burner, the heat exchanger, the ductwork, the ventilation pipes or the flue. While there are other parts that contribute to the furnace, these parts are of the most significance. Not every HVAC company sells gas furnace repair parts. If you feel competent in your knowledge of furnace repair and are looking for a part, make sure to call companies that list this as one of their services. 

Delayed Ignition Gas Furnace Repair

If you hear a large, scary ‘boom’ from your furnace every time it starts up, it is a big problem. In such cases, the furnace is essentially reporting “delayed ignition.” This will damage your furnace and possibly even burn you. Delayed ignition means that when your thermostat calls for heat from the furnace, a gas valve opens. This gas valve sends gas to the furnace’s burners to ignite the gas. When that gas isn’t ignited immediately, it allows gas to build up in the furnace. This is very bad! That’s because when the gas finally does ignite, it causes a big explosion. If you believe your furnace is suffering from delayed ignition, please contact an HVAC repairman immediately.

Gas Floor Furnace Repair

Floor furnaces distribute heat through convection, creating a hospitable environment through radiant heat. Although HVAC systems are installed in most modern houses, floor furnaces represent a suitable alternative for homeowners looking for an affordable substitute. Basic maintenance for these furnaces includes changing the air filter every thirty days in the wintertime and cleaning the air vent covers with a damp cloth every once in a while.

You need an HVAC company that knows gas furnace repair in Rutherfordton & Forest City, NC. Call Immaculate Heating and Air Conditioning LLC at 828-755-8150 to speak with our staff about making an appointment today!